This is a list of braces and boring tools for sale. Some of them will have a button to click to see a picture. Instead of having to load each image to continue, just scroll this list and click to see an image. This list has Braces, Hollow Augers, Spoke Pointers, Angle Devices, and Bits and Accessories. I'm including push drills and screwdrivers ... you can get drill bits for the screwdrivers.

Note: I have Ordering Instructions. Just click on Click To Order in any section, or right here.

  Back To Tool Index    Back to Home page

Braces

[CLICK TO ORDER]

1. STANLEY NO. 915-8-IN-X BRACE. 8-inch sweep.In very nice condition. Notched-rectangle logo on the chuck. 90%+ nickel plating. Rosewood handle and pad are very nice with a few tool-box dings, G++ ........... Sold $85.00
   Picture

2. STANLEY NO. 813-8 BRACE, 8 inch sweep. The heavy-duty chuck has a tapered hole at the top to hold tanged bits firmly. The highest quality in workmanship and materials. Bronze-bushed ball bearing head, box ratchet. Ball-bearing chuck with Universal jaws that hold all ordinary size taper shank bits, also small or medium round shank bits or drills. Almost all of the nickel plating remains. Stained hardwood handle and pad are nice with a bit of wear to the finish, Fine ......... $75.00
   Picture

3. PEXTO No. 8308 BRACE. 8-inch sweep. Ring ratchet. Alligator jaws with 1/2-inch capacity for round or square bits. Ball bearing head. 95% of the nickel plating remains, but it is a bit dull. Very nice rosewood? handle and pad, Fine .............. Sold $60.00
   Picture

4. FRAY No. 110 SPOFFORD PATENT BRACE, 10-inch sweep. The early one with just a thumbscrew to tighten the bit, but with a rosewood pad and handle with pewter ferrules, G+ ............ Sold $75.00
   Picture

5. NORTH BROS. YANKEE NO. 2100-10 IN BRACE. 10 inch sweep. An earlier one from after Stanley bought the company in the 1940s, and before the problem with the ratchet. (They started using a synthetic grease, which can harden over time, instead of oil) In extra-nice condition with 95% shiny chrome (It's chrome on the 2100) finish with minor scratches, and some dirt and tarnish in the knurling on the chuck. A brace of the highest quality. Ball Bearings throughout, Closed Ratchet. The chuck has alligator jaws that hold round, square or taper shanks up to 1/2 inch in diameter. These braces have the reputation of being the best. The handle and pad are of hard rubber that is practically indestructible, but have some minor scuffing. Very smooth ratcheting action. A great brace, Fine ................. Sold $165.00
   Picture

6. NORTH BROS. YANKEE NO. 2101-12 IN BRACE. 12 inch sweep. Pre-Stanley with 1923 and 1925 patent dates on the chuck. A brace of the highest quality. Ball Bearings throughout, Closed Ratchet. The chuck has alligator jaws that hold round, square or taper shanks up to 1/2 inch in diameter. These braces have the reputation of being the best. Has composition plastic handle and pad. Almost all of the nickel plating remains. It is completely functional. Smooth action, ratchet works great, Fine ............ $120.00
   Picture

7. MILLERS FALLS NO. 732 BRACE, 10 inch sweep. Leland patent jaws. The Holdall chuck holds regular square-tanged shanks, and round shank drills from 1/8 to 1/2 inch in diameter, and all sizes of bit stock and expansion bit shanks. Boxed ratchet. 90% of the nickel plating remains. The handle and pad are rosewood, and have some tool-box dings, Fine .............. Sold $65.00
   Picture

8. ZENITH BRACE, 10 inch sweep. I don't know who made it for them. It looks like it may have been PEXTO. 80% nickel plating. Aligator jaws. The rosewood handle and pad are very nice. A great user, G+ .............. $40.00
   Picture

9. P. S. & CO. ME-KANIK NO. MB1-10 BRACE, 10 inch sweep.Early PEXTO. A high-quality brace with The Samson patent chuck that holds tanged bits up to No. 2 Clark's Expansion bit, and and any shank 1/8 to 1/2 inch in diameter. The rosewood handle and pad are very nice. Missing some nickel plating, G++ ........... $50.00
   Picture

10. PEXTO 110, 10 inch sweep. I don't see many of these. Pexto made high-quality tools. This one looks like it is from WW II. Has cadmium plating and hardwood handle and pad. The chuck holds ANY shank bits, 1/8 to 1/2 inch capacity. Has some light rust, G+ ........... $40.00
    Picture

11. LAKESIDE BRACE, 10 inch sweep. This is an early brace that looks like it was made by Pexto. It has the long ball-bearing chuck, designed for carpenters using tanged auger bits. 80% of the nickel plating remains. Closed ratchet. Rosewood head and handle, G+ ........... $40.00
    Picture

12. STANLEY NO. 921-12 BRACE, 12-inch sweep. An early one with the Stanley Rule & Level Co.mark on the chuck and 1902, and 1904 patent dates at the top of the ratchet. The highest quality in workmanship and materials, together with the novel design, place these braces in a class by themselves as to strength, durability and appearance. Rosewood head and handle are very nice. Ball bearing head, concealed ratchet that keeps out dirt and moisture, and alligator jaws that hold all ordinary size taper shank bits, also small or medium round shank bits or drills. Missing some of the plating, G+ ....... $65.00
    Picture

13. P. S. & W. NO. 8012E BRACE, 12 inch sweep. A high-quality brace with the Samson patent chuck. Clean with some wear to the nickle plating. The handle and pad are missing their finish and have some minor dings and wear. A very good user, especially for larger work, G+ ........... $60.00
    Picture

14. STANLEY NORTH BROS. YANKEE NO. 2100-12 IN BRACE. 12 inch sweep. Pre-Stanley with the 1923 and 1925 patent numbers on the ratchet. In very nice condition. A brace of the highest quality. Ball Bearings throughout, Closed Ratchet. The chuck has alligator jaws that hold round, square or taper shanks up to 1/2 inch in diameter. These braces have the reputation of being the best. Very smooth ratcheting action. The handle and pad are of hard rubber that is practically indestructible. 90% of the nickel plating remains. Smooth ratchet. Tight and operates perfectly. A great brace, Fine ............ .............. Sold $145.00
    Picture

15. NORTH BROS. YANKEE NO. 2101-12 IN BRACE. 12 inch sweep. Pre-Stanley with the 1923 and 1925 patent numbers on the ratchet. A brace of the highest quality. Ball Bearings throughout, Closed Ratchet. The chuck has alligator jaws that hold round, square or taper shanks up to 1/2 inch in diameter. These braces have the reputation of being the best. Very smooth ratcheting action. Has the composition plastic handle and pad. 90% nickel plating. Has been lightly cleaned. Smooth action, works perfectly, G++ ............ $135.00
    Picture

16. LAKESIDE BRACE. 14-inch sweep, for heavier work. No number on the tool. Good quality chuck. Rosewood handle and pad are nice. Good nickel plating, G++ .............. $75.00
    Picture

17. MILLERS FALLS NO. 7312B WHIMBLE BRACE. 12 inch sweep. Completely functional. Missing some nickle plating. Some dings on the stained-hardwood handle and pad, G+ .............. Sold $85.00
    Picture

18. NORTH BROS. YANKEE NO. 75, RATCHET PUSH BRACE, Much more powerful than you would think. Has patent from 1895 to 1912. 16 1/4 inches long when closed, extends to 23 1/2 inches.
    Alligator-jaw chuck holds tanged bits up to 1/2 inch. The nickel plating has some wear and tool-box scratches, G+ ............... Sold $60.00
    Picture

Boring Machines, Auger handles, etc.

[CLICK TO ORDER]

Auger Handles
1. MILLERS FALLS NO. 3, AUGER HANDLE. For large tanged bits. Cast iron with wooden handles. 16-inches long, Fine ........... $95.00
   Picture

2. MILLERS FALLS NO. 4, RATCHET AUGER HANDLE. 15-inches long. The beefy chuck holds large tanged bits, for timber framing. Ratchets right or left or locks with no ratchet. One side handle with a swivel joint can be attached to the top for work in tight places. About 90% of the black enamel and nickel plating remains. Completely functional, Fine ........ Sold $120.00
   Picture
   Picture

3. P. S. & W. ADJUSTABLE AUGER HANDLE. Patented Mar. 20, 1888 stamped in the wood. For large tanged bits. Crisp with some dirt, G++ ........... $35.00
   Picture

4. SWAN ADJUSTABLE AUGER HANDLE. 12-inches long with fruitwood handles. The chuck holds large tanged bits. Pat April 21, (18)68 stamped in the metal, G+ ........... $60.00
   Picture

5. ENTERPRISE BUNG REAMER. It looks like it may have been made by Swan, with the Cook patent (Gedges for the Brits) bit with curved spurs to allow boring at an angle, G+ ........... $40.00
   Picture

Hollow Augers

[CLICK TO ORDER]

Hollow augers are used to cut round tenons for making chairs or wagon spokes. They are preceded with a spoke pointer to make a conical end that centers the hollow auger on the work.

A. A. Wood Hollow Auger Note: I get frequent questions for a copy of the instructions. They aren't much, but I can send you a copy. If you are having trouble with using the A. A. Wood Hollow Auger, the new original cutters have the point ground off, so then the cutter can get close to, and mostly parallel to, the throat, and the point doesn't stick out. Looking at the picture, the cutter is not ground completely parallel - it's a little wider at the outside, maybe for taking off more material as it gets wider? You should get a cleaner cut by grinding off that point. Here is a picture of one just out of the box.

1. A. A. WOOD & SONS, adjustable hollow auger. These are considered to be the Cadillac of hollow augers. Fully adjustable, cuts from 1/4 to 1 1/4 inch diameters. This one is in crisp condition, 85% of the black enamel remains. Great length to the cutter which can use a bit of tuning. There is some minor patina on the bare-metal surfaces. A very nice tool that has had little use. I'll include a copy of the instructions, G++ .......... Sold $115.00
   Picture
   Picture - Bottom

2. A. A. WOOD & SONS, adjustable hollow auger. These are considered to be the Cadillac of hollow augers. Fully adjustable, cuts from 1/4 to 1 1/4 inch diameters. 90% of the black enamel remains. There is some patina on the bare-metal surfaces. Great length to the cutter which could use a bit of sharpening. I'll include a copy of the instructions, G++ .......... Sold $100.00
   Picture
   Picture - Bottom

3. A. A. WOOD & SONS, FORE AUGER. Marked with the Nov 27, 1900 patent date on the tang. Made to cut a 1 1/4 inch diameter tenon with a tapered shoulder. Then you can use a hollow auger for a smaller size. Will work on stock up to 2 7/8 inch diameter. It has a depth stop.
   This seems to be especially suited for use making twig or pole furniture. The tapered shoulder adds a decorative touch and is a good way to mate the shoulder of the tenon with the curved, irregular surface of another branch. This rare tool is the only I have seen that will do this job.
   Good length to the cutter. Almost all of the black enamel remains, Fine .......... $165.00
   Picture
   Picture - Bottom

4. GOODELL PRATT HOLLOW AUGER. Dec. 5, 1911 patent date. Complete with graduated depth stop. Adjusts to any size you want from probably 1/4- to 1 1/4- inches. Very nice condition, but some of the paint has flaked off, G++ ................... Sold $80.00
   Picture
   Picture - Bottom

5. SMITH PATENT ADJUSTABLE HOLLOW AUGER. Pat'd July 17, 1866. An early idea for an adjustable hollow auger that adjusts to any size within its range. The tang is also an adjustable depth stop, G ........... $60.00
   Picture
   Picture

6. E. C. STEARNS, ADJUSTABLE HOLLOW AUGER. Cuts any size tenon from 1/4 to 1 1/4 inches. The pivoted clam-shell jaws are provided with a graduated scale by which the size of the tenon is regulated. Complete with depth stop. Completely functional It could use a light cleaning, Good ........... $75.00
   Picture
   Picture - Bottom

7. STEARNS ADJUSTABLE HOLLOW AUGER. Revolving disk has eight fixed holes that cut from 3/8 to 1 inch diameter. Has the depth stop. 95% black enamel remains, Fine ........... $70.00
   Picture
   Picture

8. MILLERS FALLS BRACE with Fixed Hollow Auger. 14-inch sweep. The fixed hollow auger is complete with the depth stop. Nice rosewood handle and pad, G+ ............... $125.00
   Picture

Spoke Pointers

[CLICK TO ORDER]

Spoke pointers are used to make a conical end on your stock to precede the hollow auger. Provides a firm start that is centered on the work. Dowel pointers are for smaller work, and can be used to chamfer (bevel) the tips of pegs for gluing joints.

1. STANLEY NO. 22 DOWEL SHARPENER. Tanged end. Used to chamfer the edges of dowels for gluing-up joints in table tops or cabinet doors. It also points small stock for chairs or twig projects, for tenoning with a hollow auger. Has had little use. All of the nickel plating remains.Has had little use, G++ .......... $40.00
   Picture
   Picture - Bottom

2. SPOKE POINTER, SMALL NO. 1 SIZE. This one is unmarked as usual, but probably made by Stearns. The adjustable, graduated tang is also a depth stop. Points up to 1 3/4 inch diameters. Very nice condition with little use. Some tool-box dings to the black enamel, Fine .............. $65.00 stanley_36half_rule_back.jpg
   Picture
   Picture - Bottom

3. SPOKE POINTER, SMALL NO. 1 SIZE. This one is unmarked as usual, but probably made by Stearns. The adjustable, graduated tang is also a depth stop. Points up to 1 3/4 inch diameters. Not much finish, but has some patina. Has been lightly cleaned, G .............. $50.00
   Picture
   Picture - Bottom

4. BATES MANUF. CO. SMALL SPOKE POINTER. Cuts up to 1 5/8 inch diameter stock. The screws all work. Most of the black enamel remains. Minor rust in the cone. The cutter needs some sharpening. A good user, G++........... $40.00
   Picture
   Picture

5. SPOKE POINTER, LARGE NO. 2 SIZE. This one is unmarked, but probably made by Stearns. The adjustable tang is also a depth stop. Points up to 2 1/2 inch diameter stock. Lots of cutter left, but it could probably use a sharpening.The black enamel finish has some wear. Has some patina on the bare-metal surfaces, G+ ............ Sold $55.00
   Picture ........... <
   Picture

6. SPOKE POINTER, LARGE NO. 2 SIZE. This one is unmarked, but probably made by Stearns. The adjustable tang is also a depth stop. Points up to 2 1/2 inch diameter stock. Lots of cutter left, but it could use a sharpening and lapping. Missing a lot of the black enamel. Has some patina on the bare-metal surfaces, G ............ $35.00
   Picture
   Picture

7. JAMES SWAN SPOKE POINTER, SMALL SIZE. This is an early one, from the late 1800s. Points up to 2 inch diameter. The outside screws help keep the cutter adjusted. About 80% of the black enamel remains. The cutter can use some sharpening and lapping, G+ ........... Sold $45.00
   Picture
   Picture

[CLICK TO ORDER]

1. STANLEY SET NO. 32 1/2 QUARTERS, No. 100 SPUR AUGER BITS. Very nice set. The genuine Russell Jennings pattern, Extension Lip Auger Bits are made of special analysis steel, forged carefully. The bits in this set have the standard double thread point, and are unsurpassed for accurate work in seasoned woods not extremely gummy or hard.
   The set has 13 bits, size 4-5-6-7-8-9-10-11-12-13-14-15-16, in 1/16th inch increments. All the sixteenths add up to 32 1/2 quarter-inches, which is where the set number comes from. The bits are extra-nice and have good tangs, spurs and lead-screws. Some may need a little touch-up with sharpening. The box has a few scuffs to the finish but the bits inside are shiny-nice, Fine ................. $325.00
   Picture - Top Tray
   Picture - Middle Tray
   Picture - Bottom Tray
   Picture - Box

2. IRWIN AUGER BITS NO. DM, in a BORECHEST, 13 Centerbore double-spur bits designed for carpentry and workshops; 1/4, to 1 inch sizes, by 16ths. The bits have had light use and have good spurs and lead screws. There is some minor tarnish on some of them. Some may need a touch-up sharpening. The box is very nice and includes original instructions. A great set, G++ ............ Sold $140.00
   Picture - Bits
   Picture - Box

3. STANLEY NO. 139 3/4 COUNTERSINK BIT, Square bit brace shanked. Two cutting flutes for wood or other soft materials. Has had light use, Fine ............ Sold $15.00
   Picture

4. STANLEY NO. 139 3/4 COUNTERSINK BIT, Square bit brace shanked. Five cutting flutes. Has had light use, Fine ............ Sold $15.00
   Picture

5. C. W. DEUSE COUNTERSINK BIT. Smaller size with a 5/8 inch wide head. New-old-stock with minor patina, Fine ............ Sold $15.00
   Picture

6. MILLERS FALLS SCREWDRIVER BIT, Made in USA, 1/4 in. Tanged for a brace. Can use some touch-up sharpening, G+ ............ Sold $12.00
   Picture

7. O. D. USA SCREWDRIVER BIT, 11/32 in. Tanged for a brace. Can use some touch-up sharpening, G+ ............ $12.00
   Picture

8. STANLEY SCREWDRIVER BIT, Sweetheart mark, 1/2 in. Tanged for a brace. Can use some touch-up sharpening, G+ ............ Sold $12.00
   Picture

9. STANLEY NO. 71 EXPANSIVE BIT, This one has three cutters that bore from 7/8 to 3-inches. I haven't seen that anywhere else. Looks to be new in the original pouch. The box is falling apart at the glue joints, Fine ............ Sold $60.00
   Picture

10. In the Box IRWIN NO. 22, EXPANSIVE BIT, Large size. Micro-dial. Has 2 cutters to drill from 7/8 to 3 inch holes. Has had little use. In the original box with instructions, Fine ............ $35.00
    Picture

11. In the Box ZENITH CLARK EXPANSIVE BIT NO. 1, Small size cuts holes from 1/2- to 1- inch. Marshall-Wells Hardware Co. Little use with some minor stain. Some damage to the box, Fine ............ $35.00
    Picture

12. C. E. JENNINGS NO. 71 EXPANSIVE BIT, Large size. Patented in 1911. Has 2 cutters to drill from 7/8 to 2 1/2 inch holes. There is a worm gear screw in the side to adjust the cutter. In a home-made box, Fine ............ $35.00
    Picture

13. STANLEY NO. 180, 18-INCH BIT EXTENSION. Made to follow bits 11/16 and larger. Most of the nickle plating remains with a bit of stain. Very nice condition, Fine ............ Sold $25.00
    Picture

14. MILLERS FALLS 18 inch EXTENSION BIT HOLDER, Has a Barber patent chuck which holds square tapered shanks and many sizes of round and irregular shanks. I think this seems to be built for a longer reach, because the chuck isn't going to follow a bit into a hole. Has been cleaned, G+ ............ Sold $55.00
    Picture

15. Boxed STANLEY NO. 59 DOWELING JIG, Complete with all six guides, 3/16, 1/4, 5/16, 3/8, 7/16, and 1/2 inch, and the bit depth stop. 99% nickel plating remains. In the original box, which is pretty nice, with the instructions. There are a few additional center finders, Fine ............... Sold $60.00
    Picture

16. Boxed STANLEY NO. 59 DOWELING JIG, A later model box. Has all six guides, 3/16, 1/4, 5/16, 3/8, 7/16, and 1/2 inch, and the later bit depth stop. Has all of the nickel plating. In the original box that has some damage. I will include a copy of the instructions, Fine+ ............... $50.00
    Picture

17. Boxed STANLEY NO. 60 DOWELING JIG, An early model with the long depth stop. Has all nine guides, 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16 and 3/4- inch. It has all of the nickel plating with a few spots of tarnish. In the original box Fine ............... Sold $80.00
    Picture

18. STANLEY NO. 47 BIT DEPTH GAUGE, for auger bits. The later style by Stanley with a springy rod. Marked Pat. Pend. All of the nickel plating remains, Fine ........ $45.00
    Picture

19. STANLEY NO. 49 BIT DEPTH GAUGE, for auger bits, like new, in its original box, which is very crisp, Fine ................ $40.00
    Picture

20. STANLEY NO. 49 BIT DEPTH GAUGE, for depth-adjustment on auger bits, close-to-new condition, Fine ................ $20.00
    Picture

21. MILLERS FALLS BIT DEPTH GAUGE, for auger bits. It has most of its nickel plating, Fine ........ $20.00
    Picture
    Picture

22. EARLY WASHER CUTTER. Unmarked by mfr. Will cut circles or washers, G+ ................ $25.00
    Picture

    Single Bits

    I've ended up with several nice bits that don't fit into any of my sets. Maybe you are looking for some to complete your set. They may need a bit of sharpening.

23. 15/16 inch DOWEL BIT BIT, An early one. Marked James Swan. 5 1/4 inches long, Fine+ ............ $20.00
    Picture

24. In the Box 3/16 inch STANLEY NO. 100, RJ BIT, New Old Stock with wrapper, Fine ............ $35.00
    Picture

25. 4/16 inch RUSSELL JENNINGS BIT, Marked Russell Jennings along shank. I have several, with or without wrapper. New-old-stock, Fine++ ............
    With wrapper ............... $20.00 each
    Without wrapper ............ Sold $15.00 each
    Picture

26. 7/16 inch STANLEY RUSSELL JENNINGS BIT, Marked Russell Jennings, Made in USA, No. 100 and size on shank. Good lead screw and spurs but may need a touch-up sharpening. Nice, G++ ............ Sold $15.00
    Picture

27. 10/16 inch STANLEY NO. 100, RJ BIT, Marked Russell Jennings, No. 100RJ, Stanley, 100 plus and Made in Australia. Some minor rust. Good lead screw and spurs but may need a touch-up sharpening, Fine ............ Sold $10.00
    Picture

28. 11/16 inch JENNINGS PATTERN BIT, Either licensed from or made by RJ for another company. Good lead screw and spurs but may need a touch-up sharpening, G++ ............ Sold $15.00
    Picture

29. 12/16 inch RUSSELL JENNINGS BIT, Marked Jennings Pattern along shank. Good length to the spurs, could use a touch-up sharpening, Fine ............ Sold $15.00
    Picture

30. 14/16 inch RUSSELL JENNINGS BIT, Marked Russell Jennings along the shank. Some patina. Good lead screw and spurs but may need a touch-up sharpening., G+ ............ Sold $15.00
    Picture

31. 15/16 inch STANLEY NO. 100, RJ BIT, Marked Russell Jennings, No. 100, Stanley, 100 plus, Made in USA, and the size on the shank. Slight modification near the top of the tang (corners filed) shouldn't effect use. May need a sharpening touch-up, Fine ............ Sold $15.00
    Picture

32. 16/16 inch RUSSELL JENNINGS BIT, Marked Stanley, Russell Jennings and Made in England along shank. Good lead screw and spurs but may need a touch-up sharpening. Some patina, Fine ............ Sold $20.00
    Picture

33. 13/16 inch RUSSELL JENNINGS 18 INCH AUGER BIT. Regular RJ double-twist pattern. Has been lightly cleaned. Could probably use some touch-up sharpening, G+ ............ $25.00
    Picture

34. 7/16 inch IRWIN BIT, new old stock, Fine ............ Sold $20.00
    Picture

35. 8/16 inch IRWIN BIT, new old stock, Fine ............ $20.00
    Picture

36. 9/16 inch IRWIN BIT, new old stock, Fine ............ Sold $20.00
    Picture

37. 10/16 inch IRWIN BIT, new old stock, Fine ............ Sold $20.00
    Picture

38. 17/16 inch IRWIN BIT,1 1/16 inch, new old stock, Fine ............ Sold $25.00
    Picture

39. 20/16 inch IRWIN BIT, 1 1/4 inch, new old stock, Fine ............ Sold $30.00
    Picture

40. 5/16 inch STANLEY H1227. Marked Stanley, H1227 and Made in USA, but IRWIN pattern. May need a touch-up sharpening, Fine ............ $15.00
    Picture

41. 14/16 inch STANLEY H1227. Marked Stanley, H1227 and Made in USA, but IRWIN pattern. May need a touch-up sharpening, Fine ............ $15.00
    Picture

Drills

[CLICK TO ORDER]

1. NORTH BROS. YANKEE NO. 550, RATCHET HAND DRILL, With five ratchet settings - plain, right- and left-hand ratchet, double-right-hand, and lock movements. The three-jaw chuck holds round or square taper bits up to 1/2 inch diameter. 18 inches overall length. The drill has been cleaned and refurbished (repainted and the metal shined) ............... Sold $85.00
   Picture
   Picture - Other Side

2. NORTH BROS. YANKEE NO. 1530A, RATCHET HAND DRILL, With five ratchet settings - plain, right- and left-hand ratchet, double-right-hand, and lock movements. 3-jaw chuck with 3/16 capacity. 10 1/2 inches long. Almost all of the nickel plating remains. The handle has some minor wear. All of the ratchets are functioning, Fine ...............$75.00
   Picture
   Picture - Back

3. NORTH BROS. YANKEE NO. 1431A, HAND DRILL, Small drill designed for radio work. Early before Stanley bought them out. 9 1/2 inches long, single speed. Three-jaw chuck with 9/32 inch capacity. In very nice condition except that there is some scoring on the handle, maybe from being in a vice. It is not rough for use. Smooth action, G++ ............... Sold $35.00
   Picture
   Picture - Back

4. MILLERS FALLS NO. 12 BREAST DRILL. Two-speed, 3 to 1 and 1 to 1. Nickel-plated extensible crank. Has a level for horizontal boring. The Master chuck holds round shank drills 1/8- to 1/2-inch in diameter, tanged bits and No.1 Morse taper shanks.
   This one is complete and in nice condition. 17 inches overall. Some crazing to the finish on the handles, Fine ...... Sold $75.00
   Picture
   Picture- Back

5. MILLERS FALLS HAND DRILL. "Buck Rogers" style.. 12 1/2 inches long. 3/8-inch three-jaw chuck. Enclosed gears. The red plastic handle unscrews to hold bits - there are none. I don't know if it came with any. Most of the gray enamel remains, Fine ...... Sold $75.00
   Picture
   Picture- Back

6. MILLERS FALLS NO. 1 HAND DRILL, An early one from late 1800s with a rosewood handle that opens to hold bits, which are missing, but there are several smaller-diameter bits included. 12 1/2 inches overall length, Three-jaw chuck holds round bits to 3/16-inch. Most of the enamel remains, Fine .......... $75.00
   Picture
   Picture- Back

7. MILLERS FALLS NO. 1 HAND DRILL, An early one from late 1800s with a rosewood handle that opens to hold bits, which are missing. 12 1/2 inches long, 3/16-inch three-jaw chuck holds any round bit, G+ .......... Sold $55.00
   Picture
   Picture- Back

8. MILLERS FALLS NO. 2 HAND DRILL. This one's the large size, 14 1/2 inches long. A strong, serviceable tool built on a sturdy cast frame. Three-jawed chuck with protected spring holds 0 to 3/8 round shank bits. Spindle equipped with ball thrust bearings. Tropical hardwood handle and the knobs are nice. Most of the red and black enamel remains. Some minor patina. Includes seven of eight original bits, G++ ...... Sold $125.00
   Picture
   Picture - Back

9. MILLERS FALLS NO. 2 HAND DRILL. This one's the large size, 14 1/2 inches long. A strong, serviceable tool built on a sturdy cast frame. Three-jawed chuck with protected spring holds 0 to 3/8 round shank bits. Spindle equipped with ball thrust bearings. Tropical hardwood handle and knobs are nice with minor dings to the finish. The handle unscrews to hold bits, there are none remaining. You can use regular twist drills. Most of the red of the black enamel remains. Some light patina. Ready to handle all of your drilling needs, G++ ...... Sold $80.00
   Picture
   Picture - Back

10. MILLERS FALLS NO. 3 HAND DRILL. Three-jawed chuck with protected spring holds 0 to 3/16 round shank bits. Tropical hardwood handle and knobs are n1ce with wear to the finish.There is a slight check in the handle. The handle twists off to hold bits, which are missing. You can use regular twist drills.The frame was nickel plated, but it's worn. 11 1/2-inches overall, G+ ...... Sold $45.00
    Picture

11. MILLERS FALLS NO.5 HAND DRILL. This is the smaller size - 12 1/2 inches long.Close to brand-new condition. A strong, serviceable tool built on a sturdy cast frame. Three-jawed chuck with protected spring holds 0 to 3/16 round shank bits. Spindle equipped with ball thrust bearings. The wide rim on the large gear can be grasped between the thumb and fingers when delicate work is being done. Most of the red and black enamel remains. Stained hardwood handle with decal, holds the set of eight original bits, Fine++ ...... Sold $155.00
    Picture
    Picture - Back

12. MILLERS FALLS NO.5 HAND DRILL. This is the smaller size - 12 1/2 inches long. A strong, serviceable tool built on a sturdy cast frame. Three-jawed chuck with protected spring holds 0 to 3/16 round shank bits. Spindle equipped with ball thrust bearings. The wide rim on the large gear can be grasped between the thumb and fingers when delicate work is being done. Almost all of red and black enamel remains. The handle and knob are stained hardwood and have some dings to the finish. The handle unscrews to hold bits, all eight are there. Smooth action, G++ ...... $120.00
    Picture
    Picture - Other Side

13. MILLERS FALLS NO. 77A HAND DRILL, 12 inches overall. 3-jaw Star chuck holds bits from 0 to 1/4 inch in diameter. Machine-cut gears. Mahogany finished hardwood handles. Some light rust, G++ .......... Sold $30.00
    Picture

14. MILLERS FALLS NO. 303 HAND DRILL, An early one from around 1900. 3/16-inch capacity three-jaw chuck holds any round bit. Hardwood handle has a slight check in the side, G+ .......... Sold $30.00
    Picture
    Picture- Back

15. GOODELL PRATT TOOLSMITHS, NO. 7 BREAST DRILL, Pat'd Mar. 31, 1896. Two-speeds controlled by a shifter knob marked fast and slow. It's 18-inches long. Two-jaw chuck will hold round bits up to 3/8- inch, G++ .......... Sold $80.00
    Picture
    Picture

16. GOODELL PRATT COMPANY, NO. 49 HAND DRILL, A very nice older small drill. 10 inches long. It has the earlier four-jaw chuck that holds the cross-top bits. Some wear to the finishes, G+ .......... $110.00
    Picture
17. GOODELL PRATT COMPANY, NO. 4 HAND DRILL, Three-jaw chuck that holds round shank drills. 10 inches long. The nickel plated handle holds bits that come out of the top as it is rotated. There are four remaining. Pat'd Nov 17, 189(...) G+ .....$80.00
    Picture

18. GOODELL PRATT TOOLSMITHS, NO. 5 1/2 HAND DRILL, Two-speed. Pat'd. MAR 31, 1896. It is 14 1/2 inchs in length. Three-jaw chuck. Hollow rosewood handle will hold bits, Foure of the eight bits remain. Has been lightly cleaned, G+ .......... $95.00
    Picture
    Picture - Back

[CLICK TO ORDER]

1. Boxed Yankee Ratchet Tool Kit No. 3600-9, Offset ratchet driver in its original box with pop-up advertising. There is a ratchet tool handle and eight bits for allen screws. About 4 inches overall, Fine ........... $60.00
   Picture
   Picture

2. STANLEY "YANKEE" NO. 3412, Offset ratchet screwdriver. Right- or left-hand action. No. 1 and No. 2 PHILLIPS Bits. About 4 inches overall, Fine ..........Sold 15.00
   Picture

3. STANLEY "YANKEE" NO. 3400, Offset ratchet screwdriver. Right- or left-hand action. 7/32 and 5/16 inch straight blades. About 4 inches overall, Fine .......... 15.00
   Picture

4. STANLEY "YANKEE" NO. 3800, Offset ratchet screwdriver. Right- or left-hand action. 3/8 and 9/16 inch straight blades. About 4 3/4 inches overall, Fine ..........Sold 15.00
   Picture

5. BMC, NO. 123, Offset ratchet screwdriver Set. Right- or left-hand action, the handle lifts and moves to each side. 3/16, 1/4, and 5/16 blades. About 4 1/2 inches overall, Fine .......... 20.00
   Picture

6. GOODELL PRATT, NO. 668, Offset ratchet screwdriver. Right- or left-hand action, the bit moves to each side. Sept 16, 1924 patent date. About 4 inches overall. 92% of the black and orange enamel remains, Fine .......... Sold 30.00
   Picture

7. Boxed STANLEY NORTH BROS., "YANKEE" NO. 41 PUSH DRILL, Has all eight bits from 1/16 to 11/64ths, that may need a bit of sharpening. 98% of the nickel plating remains. The box has some wear, Fine ......... Sold $80.00
   Picture

8. STANLEY, NORTH BROS. "YANKEE" NO. 41Y, PUSH DRILL, Has all eight bits from 1/16 to 11/64ths. Virtually all nickel plating remains. Owner's name on side. Some of the bits may need a touch-up sharpening, Fine 13H37......... Sold $55.00
   Picture

9. STANLEY, NORTH BROS. "YANKEE" NO. 41Y, PUSH DRILL, Has all eight bits from 1/16 to 11/64ths. 90% of the nickel plating remains. Some of the bits may need a touch-up sharpening, G++ 10C07......... $50.00
   Picture

10. STANLEY,"YANKEE" NO. 45, PUSH DRILL, Bakelite handle holds all eight bits from 1/16 to 11/64ths which are in nice condition but some could use a bit of cleaning and/or touch-up sharpening. They are the same as the No. 41, G++ ......... Sold $50.00
    Picture

11. Boxed NORTH BROS."YANKEE" NO. 233H Quick-Return, Spiral Ratchet Screwdriver, Comes with both flat screwdriver bits and three drill points, Fine ......... $45.00
    Picture

12. Boxed MILLERS FALLS NO. 188A AUTOMATIC PUSH DRILL, complete with 8 bits. This is the MF style of the Yankee No. 45. It has the advantage of 8 holes in the top to hold the bits, so, just turn to the size you want. The bits are the Millers Falls style with the cross-top, and are in nice condition. The box has some wear, Fine .......... $60.00
    Picture

13. STANLEY NORTH BROS. "YANKEE" NO. 30A , Spiral Ratchet Screwdriver, This is the smaller one (compared with the 131), with the original three straight bits. In the original box .......... $55.00
    Picture

14. Boxed NORTH BROS."YANKEE" NO. 35, Right- and Left-hand Spiral Ratchet Screwdriver. This is the smallest one, 12 inches long when extended. Comes with all three flat bits. Very crisp with solid brass, maybe WWII. The box is very nice, Fine .......... Sold $40.00
    Picture

15. Boxed NORTH BROS."YANKEE" NO. 135, Spiral Ratchet Screwdriver, Quick return ( means it's got a spring ) screwdriver, This is the smallest one, 12 inches long when extended. Comes with all three flat bits. Very crisp with great plating. The box has some wear, Fine .......... Sold $50.00
    Picture

16. STANLEY "YANKEE" NO. 135A, Spiral Ratchet Screwdriver, Quick return (means it's got a spring). Includes all three flat bits. Nice nickel plating with some minor wear to the finish on the handle, Fine .......... Sold $35.00
    Picture

17. MILLERS FALLS NO. 55, RATCHET SCREWDRIVER, Small one with a three-inch blade, G++ .......... Sold $30.00
    Picture

18. NORTH BROS. "YANKEE" NO.15A, RATCHET SCREWDRIVER, 3 3/4 inch blade length, 6 1/4 inches overall. Blued finish and Made in the United States of America, looks like it's from WW II. Close to brand-new, Fine ......... Sold $25.00
    Picture

19. NORTH BROS. "YANKEE" HANDYMAN NO. 2H, RATCHET SCREWDRIVER, The whole tool is only four inches long, Fine .......... Sold $15.00
    Picture

20. NORTH BROS. "YANKEE" NO. 12, RATCHET SCREWDRIVER, Stubby 1 1/8 inch blade length, Red wood handle. The screwdriver looks like new, but the 5/32nd blade has been sharpened a bit, Fine .......... Sold $20.00
    Picture

21. STANLEY "YANKEE" NO. 15, RATCHET SCREWDRIVER, 5 1/2 inch blade length. Painted wood handle has some worn finish. Nice nickel plating, G+ ......... Sold $30.00
    Picture

22. NORTH BROS. "YANKEE" NO. 15, RATCHET SCREWDRIVER, 3 inch blade length, 5 3/4 inches overall. Stained wood handle. Has the Nov-2-97 and May-1-06 patent dates. Some scuffs and dings on the handle and some patina on the blade. This one fits in the No 100 Yankee Tool Set, G+ ......... $25.00
    Picture

[CLICK TO ORDER]

MILLERS FALLS AND GOODELL PRATT PUSH DRILLS ...

1. MILLERS FALLS NO. 402 FLUTED DRILL POINTS, A complete set of eight early bits with the cross-top for the four-jaw chucks that fit the early Millers Falls and Goodell Pratt push drills. In the original tube with label. There is only a few of spots of light rust - my camera makes them look worse than they are, Fine ................. Sold $40.00
   Picture

   STANLEY No. 33, 35, 133, 135, 233, SERIES PUSH DRILLS ... These will also fit Millers Falls and Craftsman.

   1. STANLEY "YANKEE" NO. 333H DRILL BIT SET, but will fit the other screwdrivers in this section. Three drill points, 1/16th, 7/64, and 9/64, in the original plastic tube with label, Fine+ ..................... Sold $15.00
      Picture

   2. SCREWDRIVER BIT SET , I don't know the manufacturer, it may be Millers Falls, but will fit all the screwdrivers in this section. Three drill points and two screwdriver bits, in the original plastic tube, Fine+ ..................... $25.00
      Picture

   3. STANLEY YANKEE" DRILL POINTS, I have only the 7/64 and 9/64 left. New Old Stock ................. $4.00 each
      Picture

   4. STANLEY "YANKEE" Chuck adapter for drill points, N O S. Will hold the eight No. 41 drill points .......... $8.00 ea.
      Picture

   5. STANLEY "YANKEE" SCREWDRIVER BIT SET, A 5/32, 3/16, and 1/4 inch straight bit. These are the sizes that came with the No. 35 & 135. They will fit the other numbers, but are too long to fit in the handle. New Old Stock ................ $15.00 ea.
      Picture

   6. STANLEY "YANKEE" SCREWDRIVER BIT, A 5/32, 3/16 0r 1/4 inch straight bit.These are the sizes that came with the No. 35 & 135. They will fit the other numbers, but are too long to fit in the handle. New Old Stock ................ $6.00 ea.
      Picture

   7. STANLEY "YANKEE" COUNTERSINK BIT, It's the top one in the picture. New Old Stock ................ $15.00 ea.
      Picture

      STANLEY No. 41, 44, 45, & 46 PUSH DRILLS ... These will also fit Millers Falls and Craftsman.

   8. NORTH BROS. "YANKEE" DRILL POINTS. Eight drill points, 1/16th to 11/64ths. Earlier ones in the original wooden tube. For the No. 41, 44, 45 and 46 push drills. I have one set left. They have had some use and may need a bit of sharpening, G+ ..................... Sold $35.00 each
      Picture

   9. STANLEY "YANKEE" DRILL POINTS. Eight No. 41 drill points, 1/16th to 11/64ths, New-old-stock. In an earlier plastic tube, Fine+ ..................... $50.00
      Picture

   10. STANLEY "YANKEE" DRILL POINTS. Eight No. 41 drill points, 1/16th to 11/64ths, New-old-stock. In a new plastic bag. I have several sets now, Fine+ ..................... Sold $40.00
       Picture

   11. STANLEY CHUCK ADAPTER & 8 DRILLS, A complete set of eight bits with a chuck adapter that fit them to the Stanley 31 and 131 push screwdrivers. These bits also fit the Yankee No. 41, 45 and 46 push drills. They have had some use and may need a bit of sharpening. In the original tube, G++ ................. $40.00
       Picture

       STANLEY No. 30, 130 SCREWDRIVER ... These will also fit Millers Falls and Craftsman.

   12. NORTH BROS. "YANKEE" Chuck adapter for drill points, N O S. Will hold the set of eight No. 41 drill bits, Fine .................................... $8.00 ea.
       Picture

   13. NORTH BROS. "YANKEE" BIT W/ SCREW-EYE HOLDER, Pat Mar 24, 08 stamped on collar. For the No. 30 (130) and No. 20. 3 1/2 inches long, New Old Stock .............. Sold $50.00 ea.
       Picture

   14. NORTH BROS. "YANKEE" BIT W/ SCREW HOLDER, For the No. 30 (130) and No. 20. Size 2 - 1/4 inch, 4 1/2 inches long. Pat Aug 27 1907 stamped on the spring, New Old Stock .............. Sold $35.00 ea.
       Picture

   15. STANLEY "YANKEE" The three bit sizes that originally came with the screwdriver. New Old Stock ................. $15.00
       Picture

   16. STANLEY "YANKEE" SCREWDRIVER BIT, A 5/16 inch straight bit. New Old Stock ................. $7.00 ea.
       Picture

   17. STANLEY "YANKEE" 68-132 PHILLIPS BIT, No. 2 size (medium) Phillips bit for the No. 30 or 130, New ................. $15.00
       Picture

   18. STANLEY "YANKEE" PHILLIPS BIT, No. 3 size (large) Phillips bit for the No. 30 or 130, New ................. $15.00
       Picture

   19. STANLEY "YANKEE" COUNTERSINK BIT, It's the middle one in the picture. Has had little use, ................ Sold $15.00 ea.
       Picture

       STANLEY No. 31, 131 SCREWDRIVER .... These will also fit Millers Falls and Craftsman.

   20. NORTH BROS. "YANKEE" Chuck adapter for drill points, N O S. Will hold the No. 41 drill bits .................................... $8.00 ea.
       Picture

   21. STANLEY "YANKEE" 3 SCREWDRIVER BITS, A 1/4, 9/32, and 5/16 inch straight bit. Complete set for the screwdriver, New Old Stock ................. $18.00
       Picture

   22. STANLEY "YANKEE" SCREWDRIVER BIT, A 1/4 inch straight bit. New Old Stock ................. $7.00 ea.
       Picture

   23. STANLEY "YANKEE" SCREWDRIVER BIT, A 5/16 inch straight bit. New Old Stock ................. $7.00 ea.
       Picture

   24. STANLEY "YANKEE" PHILLIPS BIT, No.2 Phillips bit (the most common-size one). New Old Stock from Taiwan ................. Sold $10.00 ea.
       Picture

   25. STANLEY "YANKEE" PHILLIPS BIT, No.3 Phillips bit (the big one). New Old Stock, ................. $20.00 ea.
       Picture

   ---

   Back To Tool Index Back to Homepage